Market Products and Applications

Windshield and Glass Bonding

Prep G "Black Out" Primer

Prep G is a "black out" primer to be used on glass, polycarbonate (PC) and acrylic glass (PMMA) without ceramic coating (frit) before dispensing the glazing 70-08A, 70-11 and 70-12 adhesives. Prep G glass adhesive provides ultraviolet light protection to the bond line.

Note: UV protection is required for all direct glazing bonding applications. Factory applied frits usually provide UV protection. Read and follow instructions in the Technical Data Sheet.

Resources
Prep M "Wash" Primer

Prep M improves bond strength of SMP-based products on most nonporous substrates, such as metals, and especially metal with mill-oil finish. In cases where high thermal or physical loads, especially under humid conditions requiring ultimate adhesion, use Prep M. A clean, dry and grease free substrate is necessary for ultimate adhesion. Read and follow instructions in the Technical Data Sheet.

Resources

Specialty Products

Bostik Grout Stain

Bostik Grout Stain™ is used to refreshen the appearance of grout. Available in all Bostik grout colors, Grout Stain is easy to apply and provides a long lasting seal.

Resources

Moisture Vapor Barrier Coatings

Extreme Primer

Durabond® Extreme Primer™ is a single-component, water-based primer formulated to dramatically improve the adhesion of Durabond cement patches and self-leveling underlayments to Durabond D-261™ Extreme Moisture Vapor Barrier Coating or Durabond D-250™ Moisture Vapor Barrier Coating.

D-250 Moisture Vapor Barrier Coating

A high-performance, rapid-drying, water-based, penetrating epoxy formulated to dramatically reduce moisture vapor transmission  and surface alkalinity from substrates including "freshly-poured" concrete, cement backer board, radiant heat flooring, and cement-based terrazzo prior to the installation of engineered or solid hardwood, carpet; vinyl/VCT, rubber; porcelain, marble, granite or ceramic tile floor covering. Bostik EMC is a low-odor, non-flammable, two-component system.

 

 

Handguns

51001 AVON-15" -- 20oz. Sausage Handgun

12:1 ratio; 10.1 oz. and 20 oz. sausage handgun.
Use air with ISR 70-08.

Handguns (Cartridge, Sausage, Air and Battery Powered)

DL-32-T14E (13.5 oz. Sausage Battery Powered Gun)

13.5 oz. (400 mL) sausage battery powered gun. Supplied with disposable conical nozzle for joints up to 5/8-inch. 375 lb. force.

61006 (10.1 oz. Sausage Air Gun)

10.1 oz (400 mL) sausage air gun. 100 psi maximum.

B12S20 BOS GUN (20 oz. Sausage Handgun)

12:1 ratio; sausage handgun for 20 oz. and 600 mL sausages. Use air gun with 70-08A, 70-09, 70-12 and 1152FS. Comes with three large cone nozzles and three regular nozzles.

B26Q (28 oz. Cartridge Handgun)

26:1 thrust ratio; 28 oz. cartridge handgun.

702-G01 (20 oz. Cartridge Extension Air Gun)

28 oz. cartridge air powered gun with extension for comfortable upright dispensing. 120 psi pressure. (shows joist follower)

41001 (10.1 oz. Cartridge Handgun)

7: 1 ratio; 10.1 oz. cartridges handgun for all low viscosity sealants like LoVOC Seal™, 1100FS, 1150FS, 2100SPS

41004-2T (10.1 oz. Cartridge Handgun)

7: 1 ratio; 10.1 oz. cartridges handgun for all low viscosity sealants like LoVOC Seal™, 1100FS, 1150FS, 2100SPS

B26 (10.1 oz. Cartridge Handgun)

26:1 thrust ratio; 10.1 oz. cartridge handgun for all medium viscosity sealants and adhesives; and the demands of cold weather use.

Never-Seez Anti-Seize & Lubricating Compounds

HIGH TEMP STAINLESS

A stainless steel, graphite, aluminum based antiseize compound formulated to protect up to 2200ºF against seizure and galling, galvanic and severe environmental corrosion. It was specifically designed for applications that cannot use copper or nickel based products. Tested to MIL-A-907.

MARINER'S CHOICE

Never-Seez® Mariner’s Choice is a heavy duty anti-seize and extreme pressure lubricant formulated to assure absolute parts protection against seizure, galling and corrosion in fresh and salt water environments.

Mariner’s Choice offers unparalleled resistance to water washout and the best protection in continuous high moisture environments both above and below water lines.

Resources
BLACK MOLY

Never-Seez Black Moly lubricant is designed for industrial applications requiring non-destructive assembly and disassembly where combinations of high loads, high temperatures and low speeds are encountered to reduce friction during the assembly of press-fit components. This multi-purpose extreme pressure anti-seize lubricant contains a high concentration of molybdenum disulfide. Especially effective under extreme pressures involving heavy loads and slow speed resulting in boundary lubrication conditions, Never-Seez® Black Moly withstands pressures to 500,000 psi up to 750°F (399°C).

Resources
Pipe Compound with PTFE

Never-Seez® Pipe Compound with PTFE allows greater thread engagement and more positive sealing. This product prevents corrosion and galling of threads for easy disassembly at temperatures up to 525˚F. Recommended for use on black iron, galvanized stainless steel and pressure steam pipes in contact with maleable cast iron, brass, stainless steel and galvanized fittings.

Resources

Surface Preparation

UltraFinish™

Bostik UltraFinish™ is a fast-setting, latex-fortified, Portland cement-based patch for interior use prior to the installation of hardwood, ceramic, carpet, vinyl, or rubber flooring.

This product contains Bostik’s Blockade™ Antimicrobial Protection, which inhibits the growth of bacteria, mold, or mildew on the surface of the dried cement; the dried cement resists stains caused by mold.

Resources
Webcrete 98 Premium Portland Cement Patch

Webcrete™ 98 is a premium, fast-setting, specially-formulated, latex-fortified Portland cement patch for interior use. Webcrete 98 may be used to skim coat or feather-edge finish up to 1/2” deep in one application. Floor covering can be installed in as little as an hour after application. Webcrete 98 is extremely flexible and resilient for for patching and smoothing floors prior to the installation of ceramic tile, carpet, resilient and wood flooring. The high concentration of polymer in Webcrete 98 enables the use of this product as an embossed floor leveler when mixed only with water.

Solvent Based

7132K

ADH 7132K is a kit containing Bostik 7132R/Boscodur 24T as a two component adhesive system specifically designed for use in the vacuum form bonding of PVC films to wood, fiberboards, and most porous substrates. Characterized by its high green strength, the system permits for edge trimming immediately after removal from the vacuum former.

In addition to securing strong, resilient anchorage to PVC, Bostik 7132R solvent-based adhesive displays inherently high adhesion to polyolefin foams, polyester films, most plastic laminating films, foils, sheet metal surfaces, and to cellulosics in general. Boscodur 24T is used to ensure the development of heat and creep resistant bonds.

Resources

Urethane Sealants

LoVOC Seal™ Urethane Sealant

Bostik® LoVOC Seal™ is a one-component, moisture curing, low VOC urethane sealant specifically designed to meet the demands of the transportation industry. Primarily targeted for joint/gap filling and seam/weldline applications where low shrinkage and excellent sealability is required at economical prices. LoVOC Seal™ possesses outstanding adhesion to aluminum, wood and FRP (Fiberglass Reinforced Polyester). It can be sanded and/or painted after tack free time has been achieved.

Resources
1152FS Liquid Rivet Adhesive

Bostik® Liquid Rivet™ 1152FS is a one-component, moisture curing, polyurethane adhesive that has extremely high thixotropy and cured strength. Significant product benefits include ver high green strength and initial tack, excellethn elastic high strength bonds.

Resources

SuperTak

High Performance

High Performance is the strongest 1-surface bond you can achieve from the Bostik SuperTak product line. High Performance aerosol adhesive is often used for attaching insulation, carpet or fabrics to wood or metal surfaces in vehicle or marine interior cabin construction or conversions; transportation or marine interiors; bonding swimming pool liners, or wherever strong permanent bonds between most porous and many non-porous surfaces is needed. Special adjustable nozzle valve allows for applying in a narrow-to-wide, low-to-high volume fan spray web pattern.

Resources
Trim

SuperTak Trim is a transparent adhesive which offers a soft bond line, high heat resistance and excellent green strength for both temporary (1-surface) or permanent (2-surface) bonding of lightweight materials, such as polyurethane or latex foams, fabrics or leather to a variety of porous or nonporous surfaces including wood, metals, FRP, many plastics and painted surfaces.

Resources
SuperTak General Purpose

SuperTak General Purpose is a quick-tack, specially formulated, versatile adhesive for both temporary (1-surface) or permanent (2-surface) bonding of a variety of lightweight materials, including paper, cardboard, fabric, leather, foil, foam and fiberglass to themselves, to each other or to wood, metals and some plastics. This aerosol adhesive product can be used in a variety of graphic arts applications, for labeling, carton sealing, light assembly and MRO applications.

Resources

Advanced Hybrid Polymer Technologies

70-03A SMP Elastic Bonding Adhesive

Bostik® 70-03A is a versatile, high strength adhesive used for panel bonding in truck, coach and bus manufacturing. Its good green strength reduces the need for extended assembly clamping time. Odorless, solvent-free and isocyanate-free SMP technology. Moisture curing within 15 minutes skin time. Designed for making elastomeric construction joints that require high strength. Solvent- and isocyanate-free.

Resources
70-03A SKF (Slow-Skinning) SMP Adhesive

Bostik 70-03A SKF is a slow skin forming (30 minutes) version of the 70-03A (15 minutes). Because of its slow skin time, 70-03A SKF is the ideal product for the Dual™ accelerated technology. Solvent- and isocyanate-free.

Resources
70-07A SMP Sprayable Seam Sealer

Bostik® 70-07A is a one-component, fast curing, sprayable seam sealer that can be used for underbody coating or for overlapping seams between PVS, wood, and metal. Paintable after skin formation. Sandable after cure. Solvent-free, does not shrink or bubble. Isocyanate-free.

Resources
70-09 SMP Adhesive

Bostik® 70-09 is a high green strength version of 70-05. Used for bonding mirrors. Isocyanate-, solvent-, and corrosive additive-free. Slower curing speed versus other SMP products. Comes with precut V-notch nozzle. Available in white only.

Resources
70-11 SMP Adhesive

Bostik® 70-11 is a one-component adhesive, high tensile strength; outstanding green strength, which reduces and eliminates clamping and assembly times. Contains no solvents and is isocyanate-free. 70-11 has a longer skin time than 70-08 and is ideal when used with Dual™ accelerated technology.

Resources

Sharnet Adhesives

SPE118

Sharnet SPE118 web adhesive is a hot melt adhesive produced in nonwoven form. Web adhesives handle like a fabric facilitating both intermittent and continuous processes. The Sharnet SPE118 web series is available in a range of basis weights from 11 grams to 50 grams per square yard.

Sharnet SPE118 is based on a high performance polyester polymer. This product resists repeated home launderings and bonds to a variety of textiles, urethane foams, PVC, and vinyls. SPE118 also has good resistance to oils and plasticizers.

Resources
Marine Products
ThermoGrip® H1731

Description

This freezer-grade hot melt adhesive has a moderate open time with fast set, providing superior process flexibility. It offers robust adhesion to uncoated and coated stocks, including polylaminate stocks. It also features excellent freezer resistance and can be used in blast freezer applications.

 

Benefits

  • Increased manufacturing flexibility
  • Excellent adhesion and high tack

Resources

Interested in additional ThermoGrip® H1731 information?  Contact us today!

AquaGrip™ L1231

This re-wettable adhesive delivers exceptional production versatility thanks to its moderate open time and set speed. Its innovative formulation makes for exceptionally easy clean up and improved efficiency. This liquid adhesive provides strong adhesion to most paper stocks and is available in different viscosity ranges.

Benefits:
  • Increased manufacturing flexibility
  • Saves time and money in manufacturing
Resources
ThermoGrip® H284-332

Description

An industry standard in roll-through labeling, this hot melt non-permanent adhesive is designed for convenient, easy use. With an aggressive tack, it offers excellent, reliable label pick up. This product works in conjunction with Bostik’s liquid lap adhesives.

 

Benefits

  • Increased accuracy and quality
  • Consistently picks up every label every time, even on high speed lines

Resources

Interested in additional ThermoGrip® H284-332 information?  Contact us today!

AquaGrip™ L8039

Description

With a fast set and high tack, our adhesive creates strong adhesion to treated polyolefins like PE and PP such as those used in motor oil bottles. It offers cold crack resistance and is available in different viscosity ranges.

 

Benefits

  • Increased manufacturing flexibility
  • Improved quality

Resources

Interested in additional AquaGrip™ L8039 information?  Contact us today!

Solvent Based Adhesives

LADH1231

Liquid adhesive 1231 is a solvent-based one-component pressure-bonding adhesive designed for the assembly of interior trim components of automobiles. It is a medium viscosity tan liquid adhesive designed to be spray-applied to a variety of substrates. It is suitable for contact or pressure bonding of fabric, non-woven or PO foam to fiberboard, ABS, unprimed PP or similar materials.

Resources
L7662

Bostik 7662 is a polyester based adhesive designed for use on polyolefin foam to vinyl laminating. It is recommended Boscodur 2E as a curative to develop maximum heat resistant bonds.

Resources

Hand Towels and Specialty Adhesive Remover

Bostik® Hand Towels and Specialty Adhesive Remover

Bostik® Hand Towels and Specialty Adhesive Remover is a great revolutionary, waterless cleaning towel. Cleans hands and tools in seconds with no rinsing, drying or residue. Also, removes Never-Seez® grease, adhesive, ink, paint, tar, cured or uncured urethane and other types of sealants, plus much more.

 

http://bostiksds.thewercs.com/

Resources

Moisture Vapor Protection

Vapor-Lock™ Wood Flooring Urethane Adhesive/Vapor-Retarding Membrane

Vapor-Lock™ is a new and improved one-part, trowel-applied, rapid tacking, very low permeability moisture-cure urethane adhesive and vapor retarding membrane. This scientifically formulated adhesive/membrane does NOT contain water, is virtually odorless, and has 0%-VOC's.

Vapor-Lock offers a tenacious waterproof bond to a variety or substrates and is not adversely affected by exposure to moisture, water, or alkalinity; it can also create a vapor-retarding membrane designed to reduce moderate amounts of moisture vapor transmission from the subfloor and bridge cracks that can occur in the substrate prior to or after installation (up to 1/8”).

Construction Adhesives & Sealants (One-Component)

Bostik 916 Textured Polyurethane Sealant

Bostik® 916 is a one-component, non-sag, textured polyurethane sealant. It exhibits a textured appearance for excellent transitional sealing between materials of different textures. Bostik 916 meets ASTM C920, Type S, Grade NS, Class 25, Use NT; U.S.Federal Specification TT-S-00230C, Type II, Class A.  Primary applications include perimeter sealing in mansonry, perimeter sealing of windows and doors, construction joints, and control and expansion joints.

Applicable Standards
  • ASTM C920, Type S, Grade NS, Class 25, Use NT
  • VOC: 53 g/L

Epoxy (Engineering Adhesives)

7500 Epoxy Applicator Gun

Applicator gun for two ounce, dual-barrel cartridges used for small maintenance or assembly applications. Used with a twist-on static mixer, the epoxy resin and hardener are mixed completely and dispensed accurately. Static mixers also available separately and are supplied 10 mixers per bag.

Resources
7538

Structural epoxy having high shear strength and strong adhesion to metals, woods, reinforced plastics and masonry. The best choice for bonding parts which must withstand weather, moisture and temperature fluctuations, 7538 will adhere with minimum surface preparation and has a low coefficient of expansion. Rated 3,000 psi shear strength on steel; 2.0% elongation at break. Temperature service range: -60°F to +210°F. Green color. Meets MIL-A-52194-A requirements.

Resources

Hot Melt Adhesives (Polyester)

HM4199LV

A high performance polyester adhesive designed to bond a variety of fabrics, urethane foam, and vinyl. Bostik HM 4199LV exhibits excellent high temperature resistance, excellent resistance to plasticizer migration, and resistance to water. The HM4199LV is a, fast setting adhesive with melt point of 170° C.

Resources

Cartridge Nozzles

N0Z003 (Black Conic Cartridge Nozzle)

Ideal for backfilling windshield gaskets with 70-03A or 70-08A.

(Nozzle can be used with sausage if tightened on cartridge disk adapter.)

N0Z004 (White V-Shaped Cartridge Nozzle)

Ideal for elastic bonding applications; primarily used with 70-05, 70-08, 70-09, and 70-12.

(Nozzle can be used with sausage if tightened on cartridge disk adapter.)

Hot Melt Adhesives (Polyamide)

HM4289

Bostik HM 4289 is a specially developed dimer-acid polyamide adhesive designed for automotive interior trim applications. This product bonds to a variety of substrates including wood, engineered papers, non-woven, and some plastics. HM 4289 is recommended where heat resistance over 115 ° C is required for above belt line automotive applications. It has a medium set time, low application viscosity, and a softening point of 165° C.

Resources

Cyanoacrylates

7432

Used for bonding a wide and versatile range of materials, including woods, papers, cardboard, leathers, fabrics, many metals, plastics and elastomers. Applications for this cyanoacrylate adhesive include bonding wood components or trim in furniture, hobby and craft applications, product assembly and repair. MIL-A-46050C Type II, Class 2.

Dual SMP Technology

Dual SMP400P (Gun and Kit)

The handheld Dual SMP400P Gun is designed to deliver the adhesive and the B-Component at the proper ratio. This SMP adhesive gun uses a unique static mixer to meter and mix the adhesive and B-Component together that is then dispensed to achieve a bead of adhesive that will cure "through" in hours, not days.

13.5 oz. (400 mL) sausage air powered gun dispenses sausage and B-Component together at a 50:4 ratio.

Pages